Page 1 of 1

UBD2 reader.

Posted: Wed May 14, 2014 10:08 pm
by tut
I have had the MIL light on all weekend, so if anyone has a reader I would be greatful if they could bring it along to KH tomorrow.

tut

Re: UBD2 reader.

Posted: Wed May 14, 2014 10:13 pm
by neil
I'll have mine with me tut

Re: UBD2 reader.

Posted: Wed May 14, 2014 10:34 pm
by tut
Cheers Neil.

Leaving at 0900 for MMC as Craig is going to give the car a once over before Spazz.

tut

Re: UBD2 reader.

Posted: Wed May 14, 2014 10:34 pm
by neil
I'm sure Craig will also have reader!

Re: UBD2 reader.

Posted: Wed May 14, 2014 10:57 pm
by highlander
MIL light came on when I got stuck in Edinburgh traffic picking car up from MMC.....running fine but got a heads up from Mike as to what the likely cause would be and checked/shown at Inveraray the other week.I bought the OBD2 reader from EBay and cancelled the "fault" and it hasn't reared it's annoying head again/yet.Haven't had time for the mod yet but it's a lambda probe issue for me.....2nd probe not seeing a big enough difference in the readings between the 2 probes....before and after the cat......answer is to mount the 2nd probe on a spacer so it's effectively out of the gas stream and gets a significantly differant reading.Still waiting for the spacer to arrive :cry:
Should be 2 minute job to clear the MIL light.

Re: UBD2 reader.

Posted: Thu May 15, 2014 5:34 am
by robin
Tut, I am surprised the MIL is even connected! Hopefully if they connected the MIL they also connected the OBD2 pins to the ECU, otherwise I am not sure where you'll connect the OBD2 reader?

Cheers,
Robin

Re: UBD2 reader.

Posted: Thu May 15, 2014 9:09 am
by tut
Good point Robin, will see if I can get a reply from Keith before I leave. He does not have a CAT on the car, but this was the first time that it had come on and I have already done 2,000 miles.

tut

Re: UBD2 reader.

Posted: Fri May 16, 2014 11:50 am
by r10crw
I have one but I thought you said its on a kpro, just plug this in? Ive it setup on my laptop so just come round.

Re: UBD2 reader.

Posted: Fri May 16, 2014 11:57 am
by neil
My reader worked on it last night. The code was P0106 - Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance. How did it go after we reset it tut? I didn't see you there at the end of the night.

Re: UBD2 reader.

Posted: Fri May 16, 2014 3:04 pm
by tut
It's a K100 Craig so none accessible.

I am keeping the K-Pro that you took off the old car.

tut

Re: UBD2 reader.

Posted: Fri May 16, 2014 3:07 pm
by tut
It stayed off for a while Neil then came back on. Will pass the code over to Scuffers.

Had to leave at 1900 so was only on for an hour.

tut

Re: UBD2 reader.

Posted: Fri May 16, 2014 7:47 pm
by meatball
tut wrote:It stayed off for a while Neil then came back on. Will pass the code over to Scuffers.

Had to leave at 1900 so was only on for an hour.

tut
Wondered where you went to!

Re: UBD2 reader.

Posted: Fri May 16, 2014 7:55 pm
by tut
Looked for you Campbell but you must have been pimping with someone else.

tut

Re: UBD2 reader.

Posted: Fri May 16, 2014 8:52 pm
by meatball
tut wrote:Looked for you Campbell but you must have been pimping with someone else.

tut
Such a tart!